Product Information and Technical Data

Product Description
#311 Super White Coating is a revolutionary advancement for roof coatings. The key component of this product is the “Urethane Backbone” which provides unmatched adhesion and water resistance. This product provides superior protection in ponding water situations as well.

Uses
As a reflective weatherproof coating that beautifies as it preserves and protects roofs. The coating has the ability to bridge hairline cracks that may develop, maintaining a continuous waterproof membrane. This coating can be used on most types of roof surfaces.

Benefits

• Highest quality white coating

• Excellent adhesion to EPDM

• Excellent adhesion to Foam

• UL Classified

• Meets requirements of Energy Star

• Works under ponding water

Preparation
All surfaces are cleaned and free from dust, dirt and all foreign matter. On previously coated surfaces, the old coating must have firm adhesion to be unaffected by the new coating. Metal roofs should have all rusted areas primed with a rust inhibiting primer. Surfaces with mildew growth or stains must be cleaned with a bleach solution (2 parts water to one part bleach) prior to applying this product. Rinse thoroughly. Pressure washing entire surface is recommended for best results. Defective laps and flashings can be repaired with a self adhesive seam tape or a 3-course application of alternating between layers of #311 and Polyester reinforcement. Allow repairs to cure 24-48 hours before application of roof coating. New EPDM should be allowed to cure for a minimum of one summer season prior to coating with this product. Do not Heat or thin. DO NOT APPLY IF RAIN IS EXPECTED WITHIN 36 HOURS.

Application
Protective clothing and eyewear should be used during application of this product. Always apply on a clear, warm sunny day. Apply in morning hours to allow maximum cure time. Temperatures must be above 50°F (for 24 hours) and rising, but not above 110°F. Apply with ¾” nap exterior paint roller or professional airless sprayer. First apply one coat over all seams and joints. Allow to cure for one hour or until dry, and then apply two (2) uniform coats over entire surface avoiding excessive rolling. Two full coats are needed for all applications. Allow at least 4 hours between coats and 24-36 hours for full curing. Covers approximately 50-75 s.f. per gallon per coat, depending on the surface. TOTAL COVERAGE for two (2) coat application is 35 s.f. per gallon. Keep closed when not in use.

Spray Info: 2000-3000 psi, .041 Tip Size, 1-3 GPM

Note: If roof surfaces become soiled as they age, due to the elements, Elastomeric can be cleaned with a mild solution of water and bleach. Excessive scrubbing should be avoided.

Clean-up: Clean tools with soap and water.

Precautions: Do not store at temperatures below 50°F. Keep closed when not in use. When transporting this product, ensure that lid is tight and pail secured. Do not allow pail to tumble as this may cause lid to loosen and leakage to occur. The manufacturer also disclaims liability for flat surface application where poor drainage or ponding of water may prevail. Do not reuse empty container. Dispose of in an environmentally acceptable manner.

Typical Physical & Performance Characteristics:

Warranty: #311 is a quality product using the finest raw materials available.  GlobalShield, Inc. or the seller’s only obligation shall be to replace such quantity of the product that is proven to be defective.  Neither GlobalShield, Inc. nor  the seller shall be held responsible or liable for any injury, loss, or damage, direct or indirect that occurs from the use or improper use of the product. Before use; the user shall determine the suitability of the product for the intended use; and user assumes all risk and liability.

CAUTION! Do not take internally. Close container after each use. KEEP OUT OF REACH OF CHILDREN. Use with adequate Ventilation. VOC/COS – 5 g/l max. (0.4 lbs./gal.)

Availability: Products are immediately available from GlobalShield, Inc. throughout the United States.

Cost: Cost data is available from your local GlobalShield representative.

Technical Services: GlobalShield Technical Services Department provides problem analysis and assistance in developing recommendations for special applications.  Warranty systems require inspection by GlobalShield prior to installation. Progress and final inspections are also required.

Statement of Policy and Responsibility:

GlobalShield takes responsibility for the furnishing of quality materials, and providing specifications and recommendations for their proper installation. GlobalShield does not, either itself or through its representative, practice architecture or engineering. GlobalShield offers no opinion on, and expressly disclaims any responsibility for, the structural soundness of any roof deck on which its products may be applied. Opinions of competent structural engineers should be obtained by the owner as to the structural soundness of the roof deck, or its ability to properly support the contemplated roof installation. GlobalShield accepts no liability for any failure of the roof deck or resultant damages, and no GlobalShield representative is authorized to vary this disclaimer.

GlobalShield, Inc.
320-P North Point Parkway
Acworth, GA 30102
800-374-7663
770.974.2499
Fax: 770.974.2723
Email: solov@global-shield.com
Web site: www.global-shield.com