Product Information and Technical Data

 #200 Non Fibered Aluminum Coating is a premium quality aluminum reflective coating. It is manufactured from a blend of select asphalts, solvents, special additives, and two pounds of pure aluminum pigment per gallon. When the coating is applied, the aluminum flakes form even, overlapping layers at the surface. The layers protect the coating and the roof surface below from the sun, wind, rain, ice and snow. This product meets all requirements of ASTM D-2824 Type I.

Uses
#200 is a reflective weatherproof coating that beautifies as it preserves and protects metal, composition, built-up and modified bitumen roofs.

Advantages
#200 reduces indoor building temperatures in summer by reflecting the sun's rays. It is self-preserving. Its aluminum armor reflects most of the rays of the sun which oxidize and age the asphalt base below.

Installation
Coverage
Product yield will be from .25 to .5 gallons per 100 square feet. The yield varies according to the existing surface texture. As a general rule, the smoother the surface, the less material is required.

Surface Preparation
Remove all dirt, dust, debris and standing water by brooming and by forced air where necessary and where no danger or nuisance is caused to areas adjacent to work. All loose gravel must be removed from ballasted roofs. Scrape back to a hard edge all loose or scaled coating. Make all necessary repairs to existing surface prior to coating. Split seams, blisters and cracks in existing surface should be repaired with Roof Cement. Heavily weathered or exposed felt surfaces, as well as concrete, masonry, or weathered metal should receive an application of Asphalt Primer prior to coating. All surfaces must be dry prior to application.

Application
Coating must be thoroughly stirred prior to and occasionally during use. Mechanical mixing, if practical, is recommended. Apply by spray with a standard mastic pump and gun sized by a knowledgeable pump dealer for the particular application or by pouring directly from the container and spreading with a soft roofing brush or long nap roller. Brush or roll product out uniformly and evenly, taking care not to overwork it.

#200 cleans up with mineral spirits, but do not thin the product with this or any other solvents.

For the easiest workability in cold temperatures, warm containers by storing them overnight in a room at 65° to 75° F.

Drying Time: Four hours to touch at 70° F. & 50% relative humidify.

Restrictions
Minimum application temperature is 40° F. and rising. Do not apply to areas which pond water; do not use on dead level, tar base, or existing gravel roofs. Do not apply to new asphalt roofs which have cured less than 30 days, solvent based asphalt coatings less than 30-90 days old, or to asphalt emulsion coatings that have cured for less than 30 days. Surfaces to be coated must be dry and clean and must remain so for 24 to 48 hours after application. Light rain or heavy dew will inhibit the leafing of the aluminum flakes, causing the product to dry brown. Do not use with PVC film. Do not use where material, once applied, may come into contact with potable water. Not for use on or with products containing coal tar. Do not use on slate shingles or apply directly to wood surfaces. Not for use over rubber or plastic membranes - asphalt modified only. For exterior use only.

Cautions
This product is combustible. Keep away from heat, sparks and open flame. Avoid repeated or prolonged contact with skin. If swallowed, do not induce vomiting, Contact Physician Immediately. Keep container closed when not in use. KEEP AWAY FROM CHILDREN. Product label and Material Safety Data Sheet contain further information on the safe use of this product and precautions for the safe disposal of the container. They should be read and understood prior to use.

SPECIFICATIONS

PACKAGING INFORMATION

Availability: Products are immediately available from GlobalShield, Inc. throughout the United States.

Cost: Cost data is available from your local GlobalShield representative.

Technical Services: GlobalShield Technical Services Department provides problem analysis and assistance in developing recommendations for special applications.  Warranty systems require inspection by GlobalShield prior to installation. Progress and final inspections are also required.

Statement of Policy and Responsibility:

GlobalShield takes responsibility for the furnishing of quality materials, and providing specifications and recommendations for their proper installation. GlobalShield does not, either itself or through its representative, practice architecture or engineering. GlobalShield offers no opinion on, and expressly disclaims any responsibility for, the structural soundness of any roof deck on which its products may be applied.  Opinions of competent structural engineers should be obtained by the owner as to the structural soundness of the roof deck, or its ability to properly support the contemplated roof installation. GlobalShield accepts no liability for any failure of the roof deck or resultant damages, and no GlobalShield representative is authorized to vary this disclaimer.

GlobalShield, Inc.
320-P North Point Parkway
Acworth, GA 30102
800-374-7663
770.974.2499
Fax: 770.974.2723
Email: solov@global-shield.com
Web site: www.global-shield.com