No Fiber

#125 No Fiber Roof Coating is a high quality coating manufactured with specially selected asphalts and additives. It penetrates, resaturates and revitalizes old, dry roofing felts. Designed for use on all types of smooth surface roofs, it forms a durable, weatherproof surface. Easily applied by brush or spray, it remains pliable, increasing roof service life

Uses
#125 No Fiber Roof Coating may be used as a base coat for a final coat of Aluminum or Asphalt Fibered Coating. It may also be used as a weatherproof surface coating for metal roofs. It also forms a weatherproof surface coating for roof masonry surfaces and gutters.

Installation
Coverage
Product yield to achieve desired rate will be from 1 to 3 gallons per 100 square feet. The yield varies according to the existing surface texture. As a general rule, the smoother the surface, the less material is required. Recommended application rate is 12 to 36 mils wet film thickness that will produce 8 to 24 mils dry. A mil is 1/1000 of an inch.

Surface Preparation
Remove all dirt, dust, debris and standing water by brooming and by forced air where necessary and where no danger or nuisance is caused to areas adjacent to work. All loose gravel must be removed from ballasted roofs. Scrape back to a hard edge all loose or scaled coating. Make all necessary repairs to existing surface prior to coating. Split seams, blisters, and cracks in existing surface should be repaired with GlobalShield Roof Cement and reinforced with GlobalShield Polyester. Metal roofs should be allowed to weather for six months prior to coating.

Application
Apply by spray with a standard mastic pump and gun sized by a knowledgeable pump dealer for the particular application or by pouring directly from the container and spreading with a standard roofing brush. Be sure to spread product evenly.

#125 No Fiber Roof and Metal Coating cleans up with mineral spirits, but do not thin the product with this or any other solvents.

For the easiest workability in cold temperatures, warm containers by storing them overnight in a room at 65° to 75° F.

Drying Time: Four hours to touch at 70° F. & 50% relative humidify. Allow 7 to 14 days before any exposure to foot traffic.

Restrictions
Do not use with PVC film. Do not use where material, once applied, may come into contact with potable water. Not for use on or with products containing coal tar. Do not use on slate shingles or apply directly to wood surfaces. Surfaces to be dry and clean and must remain so for 24 to 48 hours after application. Not for use over rubber or plastic membranes - asphalt modified only. For exterior use only.

Cautions
This product is combustible. Keep away from heat, sparks and open flame. Avoid repeated or prolonged contact with skin. If swallowed, do not induce vomiting, Contact Physician Immediately. Keep container closed when not in use. KEEP AWAY FROM CHILDREN. Product label and Material Safety Data Sheet contain further information on the safe use of this product and precautions for the safe disposal of the container. They should be read and understood prior to use.

Percent Solids by Weight	68%
Percent Solids by Volume	63%
Weight Per Gallon: Pounds	7.7
Flash Point	105° F (Seta C.C.)
P.H.	N/A
Viscosity at 77° F.	800 cps.
Long-Term Service Temperature	-25° F. to +155° F.
Water Resistance: Intermittent Exposure	Excellent
Water Resistance: Ponded	Fair
Solvent Resistance	Poor
U.V. Resistance	Good

Product Number	Size	Quantity	Weight
125-055	55 gal.	Each	490 lbs.
125-005	5 gal.	Each	40 lbs.

Technical Services: GlobalShield Technical Services Department provides problem analysis and assistance in developing recommendations for special applications. Warranty systems require inspection by GlobalShield prior to installation. Progress and final inspections are also required.

GlobalShield takes responsibility for the furnishing of quality materials, and providing specifications and recommendations for their proper installation. GlobalShield does not, either itself or through its representative, practice architecture or engineering. GlobalShield offers no opinion on, and expressly disclaims any responsibility for, the structural soundness of any roof deck on which its products may be applied. Opinions of competent structural engineers should be obtained by the owner as to the structural soundness of the roof deck, or its ability to properly support the contemplated roof installation. GlobalShield accepts no liability for any failure of the roof deck or resultant damages, and no GlobalShield representative is authorized to vary this disclaimer.

Product Information and Technical Data

Availability and Costs: